Plasker Screws 3

DUROCK TEK

Rib design under head countersinks into dense material while preventing stripouts.
Two point types for steel and wood applications.
Larger head diameter increases board surface contact for greater pullover resistance.
Rock-On is recommended for ACQ treated wood.

8 x 1-1/4	M	2156500
8 x 1-5/8	M	2159500
8 x 2-1/4	M	2139500
9 x 1-1/4	M	2131500
9 x 1-5/8	M	2153500
9 x 2-1/4	M	2155500

REAMER TEK

Plywood roof and floor sheet to steel frames.
2 x 4 headers to steel frames.
Plywood fascia to steel frames.
Wood mansard to steel frames.

10 x 1-7/16	M	1082000
12 x 2-1/4	M	1092000
12 x 2-3/4	M	1094000

TEK-5 Self-Drilling

Metal deck to structural steel or bar joist.
Clips to structural steel or bar joist.
Liner panels to structural steel or bar joist.
Accessories to structural steel or bar joist.
Longer length fasteners can be used in retrofit clip and sheet applications

12 X 1-1/4

1006000

HWH TEK-3

Roof deck to steel framing. Wall panel to girt.
Duct work to steel framing. Accessories to steel framing.
Clip to steel framing. Retrofit framing.
Commercial overhead steel doors, hinges & latches.

12 X 3/4

1134000

Low Profile TEK

Low profile architectural metal roof clips to steel purlin.
Low profile architectural metal roof clips to wood supports.

10 x 1 TEK-3	M	1560553
10 x 1 Sharp	M	1596553

Coarse thread, bugle head screw for general purpose interior wood applications.

6 x 1-1/8	5 lb. Box	V200
6 x 1-5/8	5 lb. Box	V400
7 x 2	5 lb. Box	V500
8 x 2-1/2	5 lb. Box	V900
8 x 3	5 lb. Box	V1100
6 x 1-1/8 (Yellow Zinc)	5 lb. Box	V200YZ
6 x 1-1/4 (Yellow Zinc)	5 lb. Box	V300YZ
6 x 1-5/8 (Yellow Zinc)	5 lb. Box	V400YZ
7 x 2 (Yellow Zinc)	5 lb. Box	V500YZ
8 x 2-1/2 (Yellow Zinc)	5 lb. Box	V900YZ
8 x 3 (Yellow Zinc)	5 lb. Box	V1100YZ

GRABBERGARD

Coarse thread, bugle head screw for general purpose exterior wood applications.

6 x 1	5 lb. Box	V100RG
6 x 1-1/4	5 lb. Box	V300RG
6 x 1-5/8	5 lb. Box	V400RG
7 x 2	5 lb. Box	V500RG
8 x 2-1/2	5 lb. Box	V900RG
8 x 3	5 lb. Box	V1100RG
10 x 3-1/2	5 lb. Box	V1200RG
10 x 4	5 lb. Box	V1300RG

STREAKER SHARP

Fine thread bugle head screws for drywall and general interior applications. Super sharp 30° Streaker Point means quick and easy penetration into light gauge metal or wood.

6 x 1	5 lb. Box	V168
6 X 1-1/8	5 lb. Box	V268
6 X 1-1/4	5 lb. Box	V368
6 X 1-5/8	5 lb. Box	V468
7 X 2	5 lb. Box	V768
8 X 2-1/2	5 lb. Box	V968
8 X 3	5 lb. Box	V1168
10 X 3-1/2	5 lb. Box	V1268
10 X 4	5 lb. Box	V1368
10 X 4-1/2	5 lb. Box	V1468
10 X 5	5 lb. Box	V1568
10 X 6	5 lb. Box	V1768

SCAVENGER FINE

Designed for drywall to light metal applications. Scavenger head eliminates drywall paper burrs, creating a smooth professional finish. With a super sharp 30° Streaker Point you get quick and easy penetration into metal studs.

6 x 1-1/8	5 lb. Box	268S
6 x 1-3/4	5 lb. Box	568S

LAMINATING

No. 10 gauge, coarse thread screw used for fastening one layer of drywall to another. . .and a whole lot more. Also used for interior wood projects where shear strength is important.

10 X 1-1/2

5 lb. Box

V12

TRIM HEAD STREAKER

Used to attach wood, metal or plastic trim to light gauge metal or wood. Streaker Point means quick and easy penetration while the smaller, less noticeable head provides a finished look.

7 X 1-5/8	5 lb. Box	V17S
7 X 2-1/4	5 lb. Box	V18S

WAFER HD SHARP

Used for light gauge metal applications where low profile head exposure is desired.
Streaker point means quick and easy penetration into metal (25-20 ga.), while wafer head provides greater bearing surface. The right screw for K-lath installation.

8 x 9/16	5 lb. Box	V31Z
8 x 1	5 lb. Box	V32Z
8 x 1-1/4	5 lb. Box	V33Z

WAFER HD DRILLER

Wafer head, drill point framing screws for heavy gauge metal applications.
Wafer head provides a greater bearing surface than Pan or Hex Drillers, with
a low-profile head exposure.

8 X 1/2	5 lb. Box	V234FZ
8 X 1	5 lb. Box	V35Z
8 X 1-1/4	5 lb. Box	V36Z

PAN HEAD SHARP

Used in light gauge metal to metal applications where high torque is required.
Super sharp 30° Streaker Point means quick and easy penetration.

7 X 7/16

5 lb. Box

V23

The complete line of Plasker and Associates interior and exterior drywall screws meets or exceeds tthe applicable ASTM (American Society for Testing and Materials) requirements in ASTM Designation C 1002, Standard Specification for Steel Drill Screws for the Application of Gypsum Board, first published in September, 1983.

Back to Fasteners Page 1 Page 2 Page 3